Material Selection Guide for Rubber Clips Used for Fixing, Locking and Connection

A technical reference for engineers, product designers and buyers specifying elastomeric retaining clips, clamping clips and connection clips.


1. Why the material decision matters more than the shape

A rubber clip looks like a simple part. It is a shaped piece of elastomer that holds two things together, stops something from moving, or bridges a connection while absorbing tolerance and vibration. Because it is simple, it is often specified late in a project, chosen by colour or by what was already in the sample box, and never validated properly. That is usually where problems begin.

The performance of a clip is governed less by its geometry than by the elastomer compound behind it. Two clips with identical drawings can behave completely differently after six months in service: one keeps its clamping force, the other relaxes and lets the joint rattle; one survives three summers on a rooftop, the other cracks at the first sign of ozone; one leaves a permanent brown stain on a painted panel, the other leaves nothing. All of these outcomes trace back to the choice of polymer, the hardness, the curing system and the additives in the compound.

This guide sets out a structured way to make that choice. It covers the functional requirements a clip has to meet, the main elastomer families available, how hardness and compounding change behaviour, the design factors that surround the material choice, and the tests that should confirm the decision before production tooling is cut.


2. Defining the function before choosing the material

Rubber clips in fixing, locking and connection applications usually perform several jobs at once. Before comparing materials, list which of the following the part actually has to do, and rank them.

Retention or clamping force. The clip must hold a component in place against a defined load — a panel, a cable, a hose, a trim piece, a connector body. Retention depends on friction at the contact patch and on the force the clip can sustain over time, not just at the moment of assembly.

Positioning and tolerance absorption. Clips are frequently used precisely because they are compliant. They take up stack-up variation between mating parts, accommodate moulding draft, and allow a push-fit assembly that would be impossible with a rigid fastener.

Vibration and noise isolation. Elastomers convert vibration energy into heat. A clip that grips a pipe or a motor bracket can simultaneously decouple it, provided the compound has suitable damping and does not stiffen excessively at low temperature.

Sealing or dust exclusion. Some clips double as a gasket or a lip seal. In that case compression set and media resistance become the primary criteria rather than secondary ones.

Locking and release behaviour. Snap-fit and quick-release clips need a predictable insertion and extraction force, repeatable over many cycles, with limited permanent deformation after each engagement.

Electrical or thermal function. Clips used near terminals, sensors or battery modules may need dielectric strength, tracking resistance, or low outgassing and non-corrosive residues.

Once these functions are ranked, the material shortlist usually narrows quickly. A clip whose only job is to stop a cable rattling inside a dry cabinet does not need the same compound as one clamping a fuel line in an engine bay.


3. The operating environment: the real screening criteria

The second filter is the environment. Elastomers fail far more often from environmental attack than from mechanical overload, and the failure is usually slow enough to escape a short validation test.

Temperature range, including excursions. Specify continuous service temperature, peak temperature and duration, and cold-start temperature. The gap between a material’s “headline” temperature and its practical limit is often large: a compound rated to 150 °C may still be usable at 150 °C, but its compression set at that temperature may be far worse than at 100 °C. Low-temperature behaviour matters as much — a clip that becomes brittle at −20 °C will crack during winter assembly, not in the lab.

Fluids and chemicals. Engine oil, gear oil, fuel, coolant, brake fluid, hydraulic oil, cleaning agents, disinfectants, hot water, steam, seawater, and hand creams all have distinct effects. Oil resistance and water resistance are close to mutually exclusive in elastomers, so this single question frequently decides the family.

Weathering: UV, ozone, humidity. Outdoor exposure attacks unsaturated polymers through ozone cracking and UV-induced surface degradation. Ozone cracking is especially relevant to clips because a clip is almost always under strain, and strained rubber cracks far sooner than unstressed rubber.

Static versus dynamic loading. A clip that is compressed once at assembly and never moves again behaves differently from one that is cycled. Static loading makes compression set the dominant failure mode; cyclic loading adds fatigue and heat build-up.

Contact surfaces and compatibility. The clip touches painted metal, powder coat, plastic, glass, or printed circuit boards. Plasticiser migration, staining, and compatibility with the mating plastic can rule out an otherwise ideal compound.

Regulatory and market requirements. RoHS, REACH, ELV, food-contact regulations, drinking-water approvals, flame retardancy (UL 94 or equivalent), and automotive OEM material specifications all constrain the additive package, sometimes more than the polymer itself.


4. The main elastomer families and where each fits

The table below gives typical, indicative ranges. Actual values depend on the specific compound and should always be confirmed with the supplier’s test data for the exact grade being quoted.

表格

MaterialTypical service temp. (°C)Weather / ozoneOil & fuelWater / steamCompression setNotes
EPDM−50 to +150ExcellentPoorExcellentGoodBest general outdoor and water-contact choice
NBR−40 to +120PoorExcellent (aliphatic)FairGoodStandard oil-resistant clip compound
HNBR−40 to +160GoodExcellentGoodVery goodPremium option for hot oil environments
CR (neoprene)−40 to +120Very goodFair to goodGoodGoodFlame-retardant grades available
VMQ silicone−60 to +200ExcellentPoorGoodVery good at high tempWeak tear strength; migration and outgassing concerns
FVMQ−60 to +200ExcellentGoodGoodGoodSilicone with fuel/oil resistance; costly
NR−50 to +90PoorPoorGoodFairHighest resilience and tear strength; poor aging
SBR−40 to +100PoorPoorFairFairLow-cost general purpose; not for outdoor
IIR (butyl)−40 to +120GoodPoorGoodFairHigh damping, low gas permeability
TPV (PP/EPDM)−40 to +135Very goodPoorVery goodGoodRecyclable, over-mouldable, two-shot capable
TPE-S (SEBS)−40 to +100GoodFairGoodModerateSofter feel, more creep, low cost
Polyurethane−30 to +90FairGoodPoor (hydrolysis)GoodHigh strength and abrasion resistance; moisture sensitive

EPDM is the default for anything exposed to weather, water, steam or glycol. It resists ozone and UV better than almost any other general-purpose rubber, holds up in hot water, and is relatively inexpensive. Its limitation is hydrocarbon oil and fuel, where it swells badly. If a clip sits on a vehicle exterior, on HVAC equipment, in a bathroom, or around a water line, EPDM is usually the first candidate.

NBR is the standard answer for oil. It handles mineral oils, greases and aliphatic fuels well across a moderate temperature band, and is the conventional choice for clips inside gearboxes, around hydraulic lines, and in industrial machinery. It is not suitable for long outdoor exposure unless it is specially protected, and it struggles with ketones, esters and aromatic solvents.

HNBR is what NBR becomes when the application demands both oil resistance and sustained heat. It is substantially more expensive and is normally reserved for engine-adjacent or high-temperature oil-contact clips where NBR would harden and lose clamp load.

CR (neoprene) is a balanced compromise: good weathering, moderate oil resistance, decent flame behaviour, and reasonable mechanical strength. It is often chosen when a single compound must tolerate both weather and occasional oil exposure, or where a flame-retardant grade is required.

Silicone (VMQ) offers the widest temperature window and excellent retention of elasticity at both extremes. Its weaknesses are well documented and often underestimated: low tear strength, poor resistance to hydrocarbon oil, high gas permeability, and the tendency of low-molecular-weight silicone to migrate and cause contact failure in electrical assemblies or contamination in painting operations. It should not be used near electrical contacts or in paint shops without specific validation.

FVMQ addresses the oil limitation of silicone at a significant cost premium and is typically limited to specialised applications.

Natural rubber and SBR provide excellent elasticity and mechanical strength at low cost, but age poorly outdoors. They are appropriate for indoor, dry, moderate-temperature clips where cost dominates and the part is not expected to last a decade.

IIR (butyl) is selected for damping and low gas permeability rather than for strength, and is seen in mounts, seals and acoustic applications.

Thermoplastic elastomers (TPE) deserve separate consideration. TPV, based on a PP/EPDM dynamic vulcanisate, delivers much of EPDM’s weathering performance while being fully recyclable and processable by injection moulding, including two-shot over-moulding onto a rigid substrate. It has largely replaced thermoset rubber in consumer and appliance clips. Its weakness relative to vulcanised rubber is creep under sustained load, particularly at elevated temperature. TPE-S (SEBS-based) is softer and cheaper but creeps more and should not be used where long-term clamp force is critical.

Polyurethane is not an elastomer in the same sense as the families above but is frequently used for clips and clamps. It offers very high strength, abrasion resistance and load-bearing capacity, and is common in grippers, cable clamps and protective clips. Its vulnerabilities are hydrolysis in hot humid conditions and a relatively low upper temperature limit.


5. Hardness: the parameter most often mis-set

Hardness, expressed on the Shore A scale for soft elastomers, controls the trade-off between grip and rigidity.

  • 40–55 Shore A: very conformable, high real contact area, excellent grip on irregular or textured surfaces, forgiving of tolerance. Poor load capacity, high creep, easily damaged during assembly.
  • 60–75 Shore A: the usual working range for fixing and connection clips. Reasonable clamping force with enough compliance to absorb variation.
  • 80–95 Shore A: stiff, high load capacity, low deflection, suited to locking clips and structural retention. Poor conformability, sensitive to mating-part tolerance, higher insertion force.

Two practical points are frequently overlooked. First, hardness tolerance on a production compound is typically ±5 Shore A points unless tighter control is specified, which means the design should not depend on a nominal value at the edge of the acceptable band. Second, hardness and modulus are not the same thing: two compounds of equal hardness can differ substantially in compression modulus and in compression set, so hardness alone is an incomplete specification.

For clips, the more meaningful design values are the compression force at the intended interference and the retained force after ageing. Both should be requested as data, not inferred from hardness.


6. Compounding: where most real-world behaviour is decided

The polymer sets the family; the compound decides whether the part works. Four levers matter most.

Curing system. Sulphur vulcanisation gives good flex and fatigue resistance; peroxide curing gives lower compression set, better heat resistance and cleaner parts, which is generally preferable for clips that must hold force at temperature. The choice affects odour, staining and the ability to bond to metal.

Fillers. Carbon black increases strength, hardness and abrasion resistance. Light-coloured clips use silica or mineral fillers, which usually means slightly lower strength and higher cost. High filler loading raises hardness and reduces set but also reduces elongation and low-temperature flexibility.

Plasticisers. These soften the compound and improve low-temperature behaviour, but they are the most common source of field problems. Ester plasticisers migrate out of the rubber over time, and when they contact polycarbonate, ABS or painted surfaces they can cause stress cracking, fogging or permanent staining. Where a clip touches a cosmetic plastic or a coated metal panel, a compound with low migration — or a polymer that needs little plasticiser, such as EPDM or TPV — is a safer choice.

Protective additives. Antiozonants and antioxidants are essential for unsaturated rubbers in outdoor or strained service. Wax-based antiozonants form a protective surface film, which is why some outdoor rubber parts look slightly dull or bloomed; this is normal and functional, but it can be unacceptable on parts that must remain visually clean or must be printed on.


7. Design factors around the material

Material selection cannot compensate for a badly designed clip, and several design decisions interact directly with the compound.

Interference and preload. The clip must be deflected at assembly to generate force. Too little interference and retention is marginal; too much and the material sits deep in its compression set curve from day one and relaxes quickly. Typically 10–25 % compression is a sensible starting window for soft clips, refined by testing.

Contact geometry. Sharp metal edges, thread crests and burrs act as stress concentrators and will cut or tear elastomers, especially silicone and soft TPE. Radii on mating parts, or a sacrificial lip on the clip, extend life considerably.

Creep and relaxation. Under sustained load, all elastomers lose force over time; the rate depends on temperature, hardness and compound. Where loss of clamp force is unacceptable, the design should include a metal or engineering-plastic spring element that provides the preload, with the rubber supplying grip and damping rather than the entire force.

Thermal expansion mismatch. Elastomers expand considerably more than metals and rigid plastics. In a tightly toleranced assembly this can change interference noticeably across the operating temperature range, and should be checked rather than assumed.

Metal inserts and bonding. Where a clip includes a metal spring or fixing insert, the bond between rubber and metal, and the corrosion protection of the insert, become part of the specification. Salt spray testing of the assembled part, not just the coating, is the relevant verification.

Assembly force and ergonomics. Insertion and extraction forces should be measured on the actual compound. Stiff compounds that pass retention tests can still be unacceptably hard to assemble by hand or by robot.


8. Verification: the tests that actually prove the choice

A material data sheet is a starting point, not evidence. The following tests, run on the finished part geometry where possible, form a reasonable validation set.

  • Hardness: ASTM D2240 / ISO 868.
  • Tensile strength and elongation: ASTM D412 / ISO 37 — indicates whether the compound can survive expected strain.
  • Compression set: ASTM D395 Method B / ISO 815, typically 22 h at 70 °C or 24 h at 100 °C responded as a percentage. This is the single most informative test for a clip that must hold force.
  • Heat ageing: ASTM D573 / ISO 188, then re-test hardness and compression set. The relevant question is not whether the part survives, but how much force it retains.
  • Oil or fluid immersion: ASTM D471 / ISO 1817, measuring volume swell, hardness change and strength change after immersion at service temperature.
  • Ozone resistance: ASTM D1149 / ISO 1431, tested at the strain the clip actually sees. Testing unstressed samples gives misleadingly good results.
  • UV / weathering: ASTM G154 or ISO 4892 for accelerated exposure, with colour and hardness change recorded.
  • Low-temperature flexibility: ASTM D2137 brittleness point or ASTM D1329 temperature-retraction test, plus a functional cold assembly test at the specified minimum temperature.
  • Flammability: UL 94 or the relevant application standard, where required.
  • Regulatory compliance: RoHS, REACH SVHC, and any sector-specific declarations, with documentation obtained rather than assumed.
  • Functional cycling: repeated insertion and release, measuring force drift and permanent set.
  • Compatibility: direct contact testing against the actual mating plastic, coating or printed surface, at elevated temperature, to expose plasticiser migration and staining.

Where the clip is safety-related — retaining a component in a vehicle, a pressure line, or a lifting or fall-protection assembly — the validation should follow the applicable product standard rather than a generic material test set, and should include batch-to-batch verification rather than a single qualification run.


9. A practical selection sequence

  1. Define the primary function: retention, positioning, sealing, damping, or locking.
  2. List the environment: temperature range and peaks, fluids, UV and ozone exposure, humidity, and cleaning regime.
  3. Apply the two hard constraints first — fluid resistance and temperature — because these eliminate whole families and cannot be compensated by design.
  4. Select the family, then the hardness range, then confirm retained force at temperature using compression set data rather than hardness alone.
  5. Review the contact situation: mating material, cosmetic surfaces, electrical contacts, sharp edges, metal inserts.
  6. Check regulatory and market requirements against the proposed additive package.
  7. Prototype and run the validation set above on real geometry, including aged and cold conditions.
  8. Freeze the compound specification — polymer, hardness with tolerance, cure system, colour, and the test values that must be met at incoming inspection — rather than specifying only “rubber, black, 70 Shore A”.

That last step is where most quality problems are prevented. A clip drawing that names only a colour and a hardness gives a compounder almost unlimited freedom, and different suppliers will legitimately deliver different performance under the same drawing number.


10. Common failure modes and what they usually indicate

Loss of clamping force over time. Almost always compression set or creep. Look at the cure system, the filler loading, the operating temperature versus the compound’s real limit, and the initial interference.

Cracking on an otherwise intact part. Typical ozone cracking in unsaturated rubber under strain. The fix is an antiozonant, a different polymer, or reduced strain — not a thicker clip.

Surface staining, fogging or cracking of an adjacent plastic. Plasticiser migration from the clip compound. Requires a compound change, since no amount of cleaning resolves it.

Embrittlement and hardening. Usually excessive heat ageing or an incompatible fluid extracting plasticiser and attacking the polymer backbone.

Tearing at the contact edge. Stress concentration combined with low tear strength — characteristic of silicone and soft TPE against a sharp mating feature.

Electrical contact failures nearby. Silicone volatiles or corrosive residues. A specific rather than a general concern, but common enough to be worth checking early.

Unexpected swelling or softening. Fluid incompatibility that was not tested at the correct temperature or concentration; diluted coolants, bio-fuels and aggressive cleaning agents are frequent culprits.


11. Sustainability considerations

Material choice now carries an end-of-life dimension as well as a performance one. TPV and TPE-S clips are recyclable in-process and can be regrind-blended within limits, which suits high-volume consumer products and over-moulded assemblies. Thermoset EPDM and NBR clips are not easily recycled, although ground rubber is increasingly used as filler in non-critical compounds. Silicone has established take-back and pyrolysis routes in some markets but limited mainstream infrastructure. Where a product must meet recycled-content or design-for-disassembly requirements, the clip is often the easiest component to convert to TPE, provided its creep requirements permit.


12. Summary checklist

  • Identify the dominant function and the two or three environmental constraints that eliminate families.
  • Treat fluid resistance and temperature as hard filters; treat weathering, colour and cost as secondary.
  • Specify retained force and compression set, not only hardness.
  • Check plasticiser migration against every cosmetic surface the clip touches.
  • Avoid silicone near electrical contacts and in painting environments without validation.
  • Design so that a rigid element, not the elastomer alone, provides long-term preload where force retention is critical.
  • Test aged, cold and fluid-exposed parts on the real geometry.
  • Write the compound specification to the level of detail that locks in performance, and verify it at incoming inspection.

Rubber clips are small, inexpensive parts with a disproportionate effect on how a product feels, sounds and lasts. Choosing the material deliberately — from function and environment inward, rather than from colour and habit outward — is the difference between a clip that quietly does its job for ten years and one that becomes a warranty claim.


Typical property ranges quoted in this guide are indicative and vary by compound, grade and supplier. Final selection should be based on the specific material’s test data and on validation of the finished component in its intended application.

Material Selection Guide for Rubber Clips Used for Fixing, Locking and Connection

Leave a Reply

Your email address will not be published. Required fields are marked *

Scroll to top